Changing the configuration Musca / Aquarius

In the factory, the buttons have been set to a pulse function (as in, for example, a car horn) with the range limitation mode turned off and buttons 1&2, 3&4, 5&6 mutually blocked (cannot be used at the same time). It is possible to alter these settings by following the steps set out below.

Please note: the changes are to be set for all buttons at the same time.
Please note: the changes are to be set for all buttons at the same time.

By changing the configuration, already saved transmitters will be deleted. Other transmitters must be saved again.

NOTE: All Musca transmitters that were delivered before 1st of May 2018 are not equipped with this configuration.

Button function pulse / flipflop

  1. Turn off the transmitter by pressing the OFF-button for 1 second.
  2. Hold down buttons 1 and 2, then press the OFF-button as well and hold down for 5 seconds.
  3. The green LED will be on continually, the transmitter will switch to the set-up mode. You can now release the buttons.
  4. If none of the buttons is pressed for 30 seconds, the transmitter will exit the set-up mode.
  5. Press the button to be changed, until the green LED starts to blink.
  6. The button will switch to the flipflop-function. The green LED will blink 2 times (button-blocking is still active).
  7. Set the receiver to ‘programming’ mode by pressing the programming button briefly (the red LED on the receiver will switch on).
  8. Press the OFF-button of the transmitter (within 30 seconds), the yellow LED on the receiver will blink 4 times.
  9. The configuration has been saved on the receiver and the transmitter has exited the set-up mode and is switched off (green LED on the transmitter is off).
  10. Switch the power supply of the receiver off and then turn it on again to activate new settings.
  11. As a last step, switch the transmitter on and check the functionality.

Remove button-blocking for buttons that are horizontally blocked

  1. Turn off the transmitter by pressing the OFF-button for 1 second.
  2. Hold down buttons 1 and 2, then press the OFF-button as well and hold down for 5 seconds.
  3. The green LED will be on continually, the transmitter will switch to the set-up mode. You can now release the buttons.
  4. If none of the buttons is pressed for 30 seconds, the transmitter will exit the set-up mode.
  5. Press both buttons until the green LED starts to blink.
  6. The buttons-blocking will be turned off. The green LED will blink 2 times.
  7. Set the receiver to ‘programming’ mode by pressing the programming button briefly (the red LED on the receiver will switch on).
  8. Press the OFF-button of the transmitter (within 30 seconds), the yellow LED on the receiver will blink 4 times.
  9. The configuration has been saved on the receiver and the transmitter has exited the set-up mode and is switched off (green LED on the transmitter is off).
  10. Switch the power supply of the receiver off and then turn it on again to activate new settings.
  11. As a last step, switch the transmitter on and check the functionality.

Activate button-blocking for buttons that are not blocked

  1. Turn off the transmitter by pressing the OFF-button for 1 second.
  2. Hold down buttons 1 and 2, then press the OFF-button as well and hold down for 5 seconds.
  3. The green LED will be on continually, the transmitter will switch to the set-up mode. You can now release the buttons.
  4. If none of the buttons is pressed for 30 seconds, the transmitter will exit the set-up mode.
  5. Press both buttons until the green LED starts to blink.
  6. The button-blocking will be activated. The green LED will blink 2 times.
  7. Set the receiver to ‘programming’ mode by pressing the programming button briefly (the red LED on the receiver will switch on).
  8. Press the OFF-button of the transmitter (within 30 seconds), the yellow LED on the receiver will blink 4 times.
  9. The configuration has been saved on the receiver and the transmitter has exited the set-up mode and is switched off (green LED on the transmitter is off).
  10. Switch the power supply of the receiver off and then turn it on again to activate new settings.
  11. As a last step, switch the transmitter on and check the functionality.

STOP-button from pulse functionality to ‘ON relay’ latching functionality.

  1. Turn off the transmitter by pressing the OFF-button for 1 second.
  2. Hold down buttons 1 and 2, then press the OFF-button as well and hold down for 5 seconds.
  3. The green LED will be on continually, the transmitter will switch to the set-up mode. You can now release the buttons.
  4. If none of the buttons is pressed for 30 seconds, the transmitter will exit the set-up mode.
  5. Press the STOP-button until the green LED starts to blink.
  6. The button will switch to the flip-flop-functionality now. The green LED will blink 2 times (button-blocking still active).
  7. Set the receiver to ‘programming’ mode by pressing the programming button briefly (the red LED on the receiver will switch on).
  8. Press the OFF-button of the transmitter (within 30 seconds), the yellow LED on the receiver will blink 4 times.
  9. The configuration has been saved on the receiver and the transmitter has exited the set-up mode and is switched off (green LED on the transmitter is off).
  10. Switch the power supply of the receiver off and then turn it on again to activate new settings.
  11. As a last step, switch the transmitter on and check the functionality.

Range limitation mode on

  1. Turn off the transmitter by pressing the OFF-button for 1 second.
  2. Hold down buttons 1 and 2, then press the OFF-button as well and hold down for 5 seconds.
  3. The green LED will be on continually, the transmitter will switch to the set-up mode. You can now release the buttons.
  4. If none of the buttons is pressed for 30 seconds, the transmitter will exit the set-up mode.
  5. Press the ON-switch until the green LED starts to blink.
  6. The range limitation mode will switch on. The green LED will blink 2x.
  7. Set the receiver to ‘programming’ mode by pressing the programming button briefly (the red LED on the receiver will switch on).
  8. Press the OFF-button of the transmitter (within 30 seconds), the yellow LED on the receiver will blink 4 times.
  9. The configuration has been saved on the receiver and the transmitter has exited the set-up mode and is switched off (green LED on the transmitter is off).
  10. Switch the power supply of the receiver off and then turn it on again to activate new settings.
  11. As a last step, switch the transmitter on and check the functionality.

Buttons Musca Standard Configuration (blink 1x) Configuration to be activated (blink 2x)
Button 1 Pulse Hold function
Button 2 Pulse Hold function
Button 3 Pulse Hold function
Button 4 Pulse Hold function
Button 5 Pulse Hold function
Button 6 Pulse Hold function
Button 1 & 2 Mutually blocked No blocking
Button 3 & 4 Mutually blocked No blocking
Button 5 & 6 Mutually blocked No blocking
Button 1 & 3 No blocking Mutually blocked
Button 2 & 4 No blocking Mutually blocked
Button 3 & 5 No blocking Mutually blocked
Button 4 & 6 No blocking Mutually blocked
STOP-Button Pulse Relay function
ON Range limitation off Range limitation on

Revert to standard settings

In order to reset the receiver to its standard settings, you need to set only the transmitter to set-up mode and skip the changes. Or delete all transmitters from memory by pressing the programming button for 8 seconds.